Automatic Lower tank water level Controller

Our home is in municipality area .There only daily morning 5 o clock municipal drinking water supply available for an hour. so wake up at the morning collect water at that time is a hard Job. so I make this system. my idea is collect the water first in a ground level water tank when the water reach a 90% tank level an electronic Device sense that and switch on a 1/2 HP Motor that lift the water from the Lower Tank to Upper tank. once the motor start lifting the water up it only switch off when the water level reach below 10% of Lower Tank level and also when the upper tank is full . so this process running until both the tanks fill. after both Tank fill a float valve stop further water from municipal pipe line.

when the upper tank level reach certain low level if the lower Tank is full .the motor start emptying the lower tank and lift the water to up.until the lower tank level reach 10% below at Lower tank. now the pump is off and the device waiting for the next Day . so we are now completely free from taking care of daily municipal water.

There is a manual switch also include to switch the pump any time when we need.

Comments

How to read value of a Capacitor ?

Capacitance is the ability to store electrons and is measured in Farads.One Farad is a very large value! So most capacitors used in electronic circuits are measured in MicroFarads (uF) or even Picofarads (pF). Capacitance = Q / V Where Q is the charge and V is the voltage. Thus the capacitance is the charge divided by voltage. The important parameters of the capacitor are 1. Value -Value is marked on the capacitor directly or in colour codes 2. Tolerance -It indicates how much more or less the actual capacitance of the capacitor 3. Working voltage -It is the maximum voltage a capacitor can withstand before the dielectric breakdown 4. Leakage current .There is always small leakage current in all capacitors. Ideally this should be zero. But no capacitor is perfect without leakage current. Tantalum capacitor is comparatively better with minimum leakage current Value 1pf (Pico Farad) = 0.001nf (Nano Farad) 1nf (Nano Farad) = 0.001μf (Micro Farad) 1μf (Micro farad) =

Ring tester

In my Electronic repair job I found normal multimeter is somewhat limited in certain area. so special tools are needed for saving a lot of time Ring tester is one of this kind .helping me to check small hi Q inductors SMPS transformer, TV Deflection coils ,LOT ,line driver transformer and almost any inductor working on hi frequency.Normal multimeter can only identify a open coil ,but not a shorted windings. I found some commercial available ring tester. but it is not available in local shops of my area.also it seems priced high. So I decided to make a ring tester of my own. Below is the one I successfully made from the junk box components. I found it very useful. and now it is one of my best test tool collection. Two Ic's, few LED's ,one plastic container and few resistors made this wonderful tool. If we test it with primary of SMPS transformer or LOT windings of a good one shows all its LEDs will light. depending on the inductive reactantce the number of LED 's

Transistor numbers and codes

Most transistor markings follow one of these codes: JEDEC, JIS or Pro-Electron. For ICs, look for known numbers (e.g. 741, 4001, 7400) between the prefix and the suffix. Don't confuse it with the date code. ICs typically have two numbers: The part number and the date code. 1. Joint Electron Device Engineering Council (JEDEC) These part numbers take the form: digit, letter, sequential number, [suffix] The letter is always 'N', and the first digit is 1 for diodes, 2 for transistors, 3 for four-leaded devices, and so forth. But 4N and 5N are reserved for opto-couplers. The sequential numbers run from 100 to 9999 and indicate the approximate time the device was first made. If present, a suffix could indicate various things. For example, a 2N2222A is an enhanced version of a 2N2222. It has higher gain, frequency, and voltage ratings. Always check the data sheet. Examples: 1N914 (diode), 2N2222, 2N2222A, 2N904 (transistors). NOTE: When a metal-can version of a JEDEC tra

Essen Electronics

Search This Blog