Skip to main content

Posts

Electronic cheat sheet

 
Recent posts

IC PIN OUT

 

TTP223 Touch Switch Button Module

  This module is based on a touch detection IC (TTP223B) of Capacitive type touch jog switch module . This module default output low, the low-power mode to mode; when a finger touching the corresponding position, the module will output high and returns low again touch. Mode is switched to fast mode; when for 12 seconds without touching, the mode and switch to low-power mode. The module can be installed such as plastic, glass surface non-metallic materials, in addition to the thin piece of paper (non-metallic) covering the surface of the module, as long as the touch of the correct position, you can make hidden in the wall, desk and other places button.     1.Size:15*11mm 2.Power:2.5-5.5V Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level ouput; AB=01:Self-lock High TTL level ouput; AB=10:No-lock Low TTL level ouput; AB=11:Self-lock Low TTL level ouput;

LM2596 DC-DC Buck Converter Step Down Module

    A buck converter is used to step down voltage of the given input in order to achieve required output. Buck converters are mostly used for USB on the go, point of load converters for PCs and laptops, Battery Chargers, Quad Copters, Solar Chargers, and power audio amplifiers.     Features/Specs: Input Voltage: 4 ~ 40 VDC Output Voltage: 1.3 ~ 37VDC Max. Output Current: 2A Switching Frequency: 150KHz Operating Temperature: -40 to 90°C Input reverse polarity protection Built-in output short protection function The built-in thermal shutdown function Press the right key to let the display show the input or output voltage. when the right “OUT” led light, it shows output, the left “IN” led shows input. Power-off memory function, show that road after power voltage values measured for the last time Press the touch button for 3 seconds to turn off the LED display, touch the button again to turn on the LED display The band terminals, no iron can also be easy to use, and retention wire c

A02YYUW Waterproof Ultrasonic Sensor

  A02YYUW Waterproof Ultrasonic Sensor is an easy-to-use commercial-grade sensor module. This module determines the distance to a target by measuring the time lapse between sending and receiving the ultrasonic pulse. The A02YYUW sensor features a waterproof and dustproof closed separated probe that is suitable for harsh and moist environments. All the signal processing units are integrated inside the module and the distance value is directly obtained through the Asynchronous Serial Interface. The A02YYUW communicates with the upper-host or other MCU with a 9600bit/s band rate that greatly shortens the developing cycles. Specifications 3.3V-5V operating voltage range <8mA average current 3cm blind zone distance 3cm-450cm detecting range (flat object) 100ms response time -15°C~60°C operating temperature range IP

Waterproof Ultrasonic Module JSN-SR04T

  With a waterproof sealed emitter. This sensor is suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc Working voltage:5V, Static current:5mA, Working current: 40mA Working range: 25cm-4M, Working frequency: 40KHZ, Detecting angle: 70 degree Application: Horizontal distance messurement,Obstacle avoidance, automatic control, Traffic control, Security, industrial control      Specification Working voltage: DC 5V Static working current: 5mA Working current: 30mA Acoustic emission frequency:40KHz Wiring:+5V(positive); Trig(control);   Echo(receive);   GND(cathode) Connection with arduino: 5V:5V Suply Trig:D12 Echo:D13 GND:GND

Ultrasonic Sensor - HC-SR04

  The HC-SR04 is an affordable and easy to use distance measuring sensor which has a range from 2cm to 400cm (about an inch to 13 feet). The sensor is composed of two ultrasonic transducers. One is transmitter which outputs ultrasonic sound pulses and the other is receiver which listens for reflected waves. It’s basically a SONAR which is used in submarines for detecting underwater objects. Here are its main specifications: Operating Voltage 5V DC Operating Current 15mA Operating Frequency 40KHz Min Range 2cm / 1 inch Max Range 400cm / 13 feet Accuracy 3mm Measuring Angle <15° Dimension 45 x 20 x 15mm The sensor has 4 pins. VCC and GND go to 5V and GND pins on the Arduino, and the Trig and Echo go to any digital Arduino